Some armor has default vest sizes. Using a sizing chart you can estimate the closest generic size, however ordering with a sizing form will always give you the most accurate sizing.
Female vests should always be ordered with a sizing for a proper fit. In some cases male vests could be used, but it is usually not recommended.
To estimate your size to the closest generic vest size:
Measure your chest and add 2, i.e. 40+2=42.
Measure your waist and add 6, i.e. 38+6=44.
Pick the larger of the two, in this case 44.
If you have more than 6 between these two numbers average them out and if necessary round up to the nearest even number, i.e. 48μ40=44.
Measure your front length while sitting.
(Clavicle to above the navel)
13 to 14 = R and 15 to 16 = L
If your vest rises up when sitting, the SSBS Neoprene straps can be trimmed to raise the vest.
NOTE: In this case, please call us so as not to damage the product and void your warranty.
Understand that these are estimations for a quick fit; for a proper fit it's always best to order with a sizing form. The professionals at Body Armor Outlet can walk you through the process if you have any questions.
How to tell if your concealable body armor fits correctly: Concealable body armor should cover your center mass vitals, and achieve anywhere from a 2 inch gap on each side (for the most mobility) to overlapping of the ballistic panels on the sides where the front and back panels meet (for the most protection).
The first thing to remember when trying on vests is that your front panel should always lay over your rear panel as threats typically come from in front of you, and this ensures that the overlap on the side of the vest is rear facing.
A correctly sized vest will cover you from 1-1.5 inches below the top of your breastbone, to 1-2 inches above your navel (belly button) in length. The width, as mentioned earlier, should achieve anywhere from a 2 inch gap to 1" of overlapping where the front and rear panels meet. Your personal preference may dictate minor variations in comfort, mobility, concealment, and protection.
A vest that is too small for the user will lack the needed coverage to ensure proper protection with large gaps of coverage as well as being too tight and constricting, whereas a vest that is too large will shift, bunch, and crumple while it's being worn, causing pinch points and poor protection. It is a crucial step when buying body armor to ensure that it fits properly so that it performs at its peak level.
If you have any questions at all about armor sizing, don't hesitate to call us. Our highly trained staff will assist you in getting the best fit possible.
For charts, choose from one of our available sizing charts below.
Elzetta Shield Lights deliver exceptional quality and performance for tactical protection. The standard model, shown here, features a horizontal handle with an integrated solid-state tape switch.
This model provides 1,000 lumens of neutral-tint white light through two solid-acrylic flood lenses, creating a uniform "wall-of-light" that illuminates an entire room. The design ensures extreme durability with fully potted electronics and redundant circuitry, allowing continued operation even if one light source is damaged. An optional strobe feature is available.
Installation is straightforward, requiring no soldering or wire-routing, and all components are backed by a five-year limited warranty.
Specifications:
1,000 lumens of neutral-tint white light
CREE LEDs run over 2.5 hours without dimming
Two solid-acrylic flood lenses for a uniform "wall-of-light"
Fully potted electronics for extreme durability
Redundant circuitry for continued operation if one light source is damaged
Optional strobe feature
Uses five (5) CR123 batteries
Five-year limited warranty
Made in USA with American materials, tooling, and labor
Compatible Shields:
Bellfire B
Bellfire LTS
Bellfire MTS
Features:
Horizontal handle with integrated solid-state tape switch
Molded-in textured surfaces provide exceptional grip in all conditions
Straightforward installation with no soldering or wire-routing required
Simple user interface is factory pre-programmed for momentary and constant-on operation
Complete redundancy ensures system operability even if one of two LED lights is destroyed
Wide uniform beam pattern enhances situational awareness and threat assessment
Soft edge beam gradually fades into the environment to reduce tunnel-vision
Optional strobe light feature designed to disorient adversaries with high-frequency light flashes
All components sealed to provide a water-resistant all-weather system
Solid mounting via steel fasteners eliminates adhesives and threat of secondary projectiles
Solid-state switch technology guarantees maximum reliability
Fully-potted electronics lock circuit components in place for extreme durability
All wiring concealed inside the system to eliminate snag hazards
Solid-acrylic optical lenses (no reflectors) provide extreme durability and superior beam quality
Neutral-tint light renders colors accurately similar to sunlight without artificial blue color
Battery cap easily disables the system for storage and transport
Battery cap retained with integral lanyard to avoid loss and speed battery changes
