ADEN B50 1200-Watt Shield Light
Product Code: AS-DELTA-B50-1000
Availability:Out of stock
Size chart
Sizing Charts
Some armor has default vest sizes. Using a sizing chart you can estimate the closest generic size, however ordering with a sizing form will always give you the most accurate sizing.
Female vests should always be ordered with a sizing for a proper fit. In some cases male vests could be used, but it is usually not recommended.
To estimate your size to the closest generic vest size:
- Measure your chest and add 2, i.e. 40+2=42.
- Measure your waist and add 6, i.e. 38+6=44.
- Pick the larger of the two, in this case 44.
- If you have more than 6 between these two numbers average them out and if necessary round up to the nearest even number, i.e. 48μ40=44.
- Measure your front length while sitting.
- (Clavicle to above the navel)
- 13 to 14 = R and 15 to 16 = L
- If your vest rises up when sitting, the SSBS Neoprene straps can be trimmed to raise the vest.
- NOTE: In this case, please call us so as not to damage the product and void your warranty.
Understand that these are estimations for a quick fit; for a proper fit it's always best to order with a sizing form. The professionals at Body Armor Outlet can walk you through the process if you have any questions.
How to tell if your concealable body armor fits correctly:
Concealable body armor should cover your center mass vitals, and achieve anywhere from a 2 inch gap on each side (for the most mobility) to overlapping of the ballistic panels on the sides where the front and back panels meet (for the most protection).
The first thing to remember when trying on vests is that your front panel should always lay over your rear panel as threats typically come from in front of you, and this ensures that the overlap on the side of the vest is rear facing.
A correctly sized vest will cover you from 1-1.5 inches below the top of your breastbone, to 1-2 inches above your navel (belly button) in length. The width, as mentioned earlier, should achieve anywhere from a 2 inch gap to 1" of overlapping where the front and rear panels meet. Your personal preference may dictate minor variations in comfort, mobility, concealment, and protection.
A vest that is too small for the user will lack the needed coverage to ensure proper protection with large gaps of coverage as well as being too tight and constricting, whereas a vest that is too large will shift, bunch, and crumple while it's being worn, causing pinch points and poor protection. It is a crucial step when buying body armor to ensure that it fits properly so that it performs at its peak level.
If you have any questions at all about armor sizing, don't hesitate to call us. Our highly trained staff will assist you in getting the best fit possible.
For charts, choose from one of our available sizing charts below.
US Armor Sizing
Galvion
B50 1200-Watt Shield Light
Note: the B50 Shield Light is only for use with ballistic shields, like the ADEN Combat Systems ballistic shields.
ADEN's B50 is a retrofittable, front mounted 1200 lumen LED light for ballistic shields. This strobe-capable shield light provides tactical officers with panoramic lighting and immediate situation assessment to see and respond faster.
The B50 is our most powerful aftermarket shield light. It is equipped with a single pressure switch that activates the light and changes modes. This light has dual settings: On/Off and Tactical (3 modes: Momentary, Continuous On, and disorienting Turbo-Strobe™). This tactical lighting tool has a Kill Switch feature, which allows the operator to lock out the light from unintentional activation. The B50 mounts to the front of ballistic shields via industrial strength re-closable fasteners (Velcro®), which means no drilling into the shield and no compromising shield ballistics.
The lightweight B50 is powered by 18650 or CR123 batteries. The ultradurable B50 is waterproof, flame resistant, and designed for use in anti-riot situations along with dynamic and deliberate entries by SWAT, military special operations, and law enforcement around the globe.
Retrofittable Design
This light and battery pack can quickly and effectively be front mounted to shields via the included industrial 3M Dual Lock Strips fasteners (or VELCRO® mounted). This allows the light to be used and removed without causing permanent changes (holes) to the shield.
Medium Beam Pattern
The wider beam angle provides panoramic lighting and immediate situation assessment so you can see and respond faster. This is helpful in close quarters (hallways and doorways).
Durability
Our shield lights are fully waterproof, fire-resistant, impact-resistant and can be used in all-weather situations. They will hold up in challenging environments and can even be decontaminated if needed.
Turbo-Strobe™
A turbo-strobe option is included in this unit. This varying frequency strobe mode is used to disorient individuals when necessary.
Pressure Switch Activation
This model comes equipped with a single pressure switch, which is used to activate the light and change modes.
Kill Switch
This light comes with a kill switch feature. It allows the operator to lock out the light from unintentional activation.
Features:
- Single switch operation
- Turbo-strobe mode
- Kill switch
- Two program choices: either 3 Tactical modes or On/Off
- Braided steel cable
- Beam Distance: 452 ft (138 m)