Some armor has default vest sizes. Using a sizing chart you can estimate the closest generic size, however ordering with a sizing form will always give you the most accurate sizing.
Female vests should always be ordered with a sizing for a proper fit. In some cases male vests could be used, but it is usually not recommended.
To estimate your size to the closest generic vest size:
Measure your chest and add 2, i.e. 40+2=42.
Measure your waist and add 6, i.e. 38+6=44.
Pick the larger of the two, in this case 44.
If you have more than 6 between these two numbers average them out and if necessary round up to the nearest even number, i.e. 48μ40=44.
Measure your front length while sitting.
(Clavicle to above the navel)
13 to 14 = R and 15 to 16 = L
If your vest rises up when sitting, the SSBS Neoprene straps can be trimmed to raise the vest.
NOTE: In this case, please call us so as not to damage the product and void your warranty.
Understand that these are estimations for a quick fit; for a proper fit it's always best to order with a sizing form. The professionals at Body Armor Outlet can walk you through the process if you have any questions.
How to tell if your concealable body armor fits correctly: Concealable body armor should cover your center mass vitals, and achieve anywhere from a 2 inch gap on each side (for the most mobility) to overlapping of the ballistic panels on the sides where the front and back panels meet (for the most protection).
The first thing to remember when trying on vests is that your front panel should always lay over your rear panel as threats typically come from in front of you, and this ensures that the overlap on the side of the vest is rear facing.
A correctly sized vest will cover you from 1-1.5 inches below the top of your breastbone, to 1-2 inches above your navel (belly button) in length. The width, as mentioned earlier, should achieve anywhere from a 2 inch gap to 1" of overlapping where the front and rear panels meet. Your personal preference may dictate minor variations in comfort, mobility, concealment, and protection.
A vest that is too small for the user will lack the needed coverage to ensure proper protection with large gaps of coverage as well as being too tight and constricting, whereas a vest that is too large will shift, bunch, and crumple while it's being worn, causing pinch points and poor protection. It is a crucial step when buying body armor to ensure that it fits properly so that it performs at its peak level.
If you have any questions at all about armor sizing, don't hesitate to call us. Our highly trained staff will assist you in getting the best fit possible.
For charts, choose from one of our available sizing charts below.
In stock plates ship in 2-3 weeks. Out of stock plates ship in 6-8 weeks.
Guardian 4sas7 10x12 Level IV Hard Armor Plate
The Stand Alone Multi-Hit Plate with Special Threat Protection
The Guardian 4sas7™ is a cost effective level IV stand alone plate providing armor piercing protection. Engineered with a ceramic strike face and PE backing, the 4sas7 is certified compliant by NIJ to NIJ Standard 0101.04 (2005IR).
This body armor EXCEEDS Level IV NIJ certification requirements.
Specifications:
Protection: Level IV Stand Alone Armor Piercing
NIJ Standard 0101.04 (2005IR): This product has been certified compliant by the National Institute for Justice.
DEA: Hard Armor Protocol Compliant
RST: Rifle Special Threats Validated
Material: Ceramic strike face composite backing
Exterior Cover: 1000D CORDURA®, Textured Nylon
Cuts: Available in shooters cut, swimmers cut, and SAPI (10”x12” shooters cut is considered nominal 9.5”x11.5” dimensions)
Curve: Single Curve or Multi Curve
Thinness: 0.75” / 19mm
Weight: 7.2 lbs. to 9.3 lbs.
Warranty: 5 years on all ballistic material excluding exterior cover and 1 year on exterior cover material and workmanship
